- Overview
- Specification
- Documentation
- Get Started
-
PHY6212 ultra-low power consumption high-performance wireless communication system-level chip integrates a high-performance 32-bit MCU, RF sensitivity -97dBm@BLE 1Mbps, peak transceiver power 6.7/6.7mA, ultra-high energy efficiency, solves the problems of wireless connection stability and low power consumption in complex scenarios, and has a full communication protocol stack with independent intellectual property rights.
PHY62 series chips are widely used in industrial/consumer fields such as smart home, smart wearable, smart lighting, industrial control, medical health, AI voice, new energy vehicles, etc. The chips have high cost performance and high reliability, and have been delivered to more than 100 IoT customers at home and abroad.Downloads
Highlights
Flexible, secure, high-performance, low-power system-level chip architecture
Possessing one of the very few full communication solutions with independent intellectual property rights in China
High-performance multi-mode RF transceiver, average application power consumption <10uA in multiple scenarios
Powerful RF linkbuget meets the wireless application requirements of complex usage scenarios
Solve the problems of wireless connection stability and low power consumption in complex scenarios
Chip adaptive calibration, conventional device deviations meet wide temperature range, such as crystal frequency deviation, temperature drift, aging, etc.
Storage resources meet industrial-grade high-temperature reliability Storage resources meet industrial-grade high-temperature reliability
Anti-power interference, meet complex power conditions
The minimum BOM only requires [a 1uF capacitor + a 16MHz crystal oscillator]
Procotols
Scenarios
Smart Home 
Wearables 
Industrial IoT 
Logistics Pickup
Other mass-produced applications: Bluetooth beacon丨Apple Findmy丨New energy charging pile丨Electricity meter丨Fire smoke sensor丨Smart street light丨Selfie camera... -
- High-performance Low-power 32-bit processor
- Memory
- 512KB/2MB in-system flash memory
- 128KB ROM
- 138KB SRAM, all programmable retention in sleep mode
- 8-channel DMA
- 33/19 General Purpose I/O pins
- All pins can be configured as serial interface and programmable IO MUX function mapping
- All pins can be configured for wake-up
- 18 pins for triggering interrupt
- 3 quadrature decoder(QDEC)
- 6-channel PWM
- 4-channel I2S
- 2-channel PDM
- 2-channel I2C
- 2-channel SPI
- 1-channel UART
- JTAG
- DMIC/AMIC with microphone bias
- 3/8-channel 12bit ADC with low noise voice PGA
- 4-channel 24bit timer, one watchdog timer
- Real Timer Counter (RTC)
- Power, Clock, Reset Controller
- Flexible power management
- Supply voltage range 1.8V to 3.6V
- Embedded buck DC-DC and LDOs
- Battery monitor: Supports low battery detection
- Power consumption
- 0.7uA @ OFF Mode (IO wake up only)
- 2uA @ Sleep Mode with 32KHz RTC
- Receiver: 6.7mA @sensitivity level
- Transmitter: 6.7mA @0dBm TX power
- RC Oscillator hardware calibrations
- 32KHz RC osc for RTC with +/-500ppm accuracy
-
- 32MHz RC osc for HCLK with 3% accuracy
- High Speed Throughput
- Support BLE 2Mbps Protocol
- Support Data Length Extension
- Throughput up to 1.6Mbps(DLE+2Mbps)
- Support SIG-Mesh Multi-Feature
- Friend Node
- Low Power Node
- Proxy Node
- Relay Node
- 2.4 GHz transceiver
- Compliant to Bluetooth 5.4
- Sensitivity:
-97dBm@BLE 1Mbps data rate
-103dBm@BLE 125Kbps data rate
-
-
- TX Power -20 to +10dBm in 3dB steps
- Single-pin antenna: no RF matching or RX/TX switching required
- RSSI (1dB resolution)
- AES-128 encryption hardware
- Link layer hardware
- Automatic packet assembly
- Automatic packet detection and validation
- Auto Re-transmit
- Auto ACK
- Hardware Address Matching
- Random number generator
- Operating temperature:
- -40˚C ~+85 ˚C (Consumer)
- -40 ˚C ~+105 ˚C (Industrial)
- RoHS Package: QFN48/ QFN32
- Applications: wearables, beacons, appliances, home and building, health and medical, sports and fitness, industrial and manufacturing, retail and payment, security, data transmission, remote control, PC/mobile/TV peripherals, internet of things (IoT)
-
-
-
Recommended Development Tools
Evaluation BoardPHY6212 QFN32 EVBVersion: PHY6212_32_v1.0
• General list items test PHY6212_QFN32 chip current, voltage, power consumption, RF performance
• RF interface: SMA• Serial port: UART
• GPIO: All GPIOs are pinned out with standard 2.54mm pitch pins
[Download] PHY6212_32 EVB PcbDoc v1.0 [PcbDoc] [Download] PHY6212_32 EVB PDF v1.0 [PDF]PHY6212 QFN48 EVBVersion: PHY6212_48_v1.0
• General list items test PHY6212_QFN48 chip current, voltage, power consumption, RF performance
• RF interface: SMA• Serial port: UART
• GPIO: All GPIOs are pinned out with standard 2.54mm pitch pins
Contact Sales [Download] PHY6212_48 EVB PcbDoc v1.0 [PcbDoc] [Download] PHY6212_48 EVB PDF v1.0 [PDF]
Contact Us
3/F, Building 23, Lane 676, Wuxing Road, Pudong New Area, Shanghai